Unzip the file to a folder on your computer. Remove the microSD card from the AppCam. Insert the microSD card into your computer an adapter may be necessary. Copy the firmware to the root directory of your microSD card. Eject the microSD card and place back into your AppCam. Connect the power to your AppCam.
The AppCam will install the firmware. Note: It may be necessary to perform the initial setup again for the AppCam and your mobile phone application. This installer creates the following driver on your system: v2. Install Instructions. You will need this to unlock the full version of the program. There is no charge for the full version of this software. Release Notes. To enter registration key: open program, click on "write to scanner", click on "setup" at top and then "registration".
Next Page. Scanner radio with automatic scanning capabilities 96 pages. Scanner radio with trunk tracker iv and automatic scanning capabilities pages.
You can set the direction of searching as well as the speed. The Turbo Search feature, new for Uniden scanners, can search v. Unique Data Skip Allows the scanner to skip over unwanted data transmissions and reduces birdies. Memory Backup The stored channels are retained in memory for at least 3 days, and typically 14 days, when the Battery Pack is removed from the scanner.
Memory Bank Numbers — Each Memory Bank consists of 10 channels that you can select or deselect during scanning operation, using the numeric keypad. When you select a Bank, its number appears on the display. In this mode, when the scanner monitors an active frequency, searching or scanning will not resume until transmission stops for 2 seconds. Page 9 Use to enter the decimal point when programming a frequency into a channel. If you make an entry error, press erase the entry, and start over.
Press to store a displayed frequency into any displayed channel. Use or down direction within a Band, or to go up or down in frequency when Search is stopped..
After about 10 minutes, the scanner will shut itself off to prevent the battery from becoming completely discharged. Before charging, you must first install the Battery Pack according to the steps below. Place the Belt Clip on the mounting area on the back of the scanner, making sure the holes in the clip line up with the threads in the back of the scanner.
Insert the 2 screws into the corresponding holes and tighten. If the Delay Mode is on, the scanner remains on the same channel for 2 more seconds, waiting for a responding transmission. If there is no responding transmission within 2 seconds, the scanning cycle resumes. Page 13 If the Delay Mode is on, the scanner remains on the same channel for 2 more seconds, waiting for a responding transmission.
If there is no responding transmission within 2 seconds, the search cycle resumes. Page Programming Channels Directory. Program Page Programming With Search Press display will blink twice to confirm the programming. If you want to store the frequency in the selected channel 18 as well, press blink twice to confirm the programming.
Page 16 Press repeatedly to cycle through each of the 12 preprogrammed Search Bands until you see the Band you want. Wait for at least 2 seconds for Search to begin. Or press When Search stops on a desired frequency, press to stay on that frequency.
The next available empty channel will be blinking on the display. Page Scanning Note: When you turn the scanner on it will be in the same Mode it was in when you turned it off. Bank Scanning Look at the upper left corner of the display. If a transmission is received, the scanner will stop at that channel. Page Delay You may have programmed certain channels that you do not want to hear every time you scan.
These are channels that are busy a major portion of the time, and the scanner stops at the channel s often enough to interrupt the scan cycle. You can Lock Out those channels so they are not scanned.
Page Looking For "Locked Out" Channels For added convenience, there are 10 corresponding channel identifiers on a Memo Pad on the front of the scanner. Find the frequencies you want using the enclosed SportCat Frequency Guide. There are listings for all types of events, such as: Auto Racing, Boat Racing, various show tours, Golf Tournaments, and more. Page 21 a. Place the point of a ball point pen into the small hole of the Memo Pad plastic cover, and lift it off. Write the names or other identifying remarks in each channel block on the Memo Pad.
When the Weather Search finds an active channel in your area, the scanner stops at that frequency. To stay at that frequency, press Weather Search, press It is possible that you may be able to hear more than one Weather broadcast in your area. Page Searching 1 frequency step. See the table on page for the step size for each Band. A scanner will normally stop on any transmission it receives.
This means the SportCat will stop on Data signals and unmodulated transmissions. You can skip these frequencies during Search. The scanner may stop at certain frequencies during Search that you do not want to hear. You can program up to Skip Frequencies into the SportCat. When the scanner stops at one of these frequencies during Search, press. Page Care And Maintenance 4. Carefully unplug the Battery Back and lift it out of the case You may need to exert a slight pressure toward the top of the scanner as you slide the Battery Pack out of the case.
Carefully plug in the new Battery Pack, observing the proper polarity.
0コメント